Homeowner's
Glossary of Building Terms
|
Acoustical Tile
|
Special tile for walls and ceilings made of
mineral, wood, vegetable fibers, cork, or metal. Its purpose is to
control sound volume, while providing cover.
|
Air Duct
|
Pipes that carry warm air and cold air to
rooms and back to furnace or air conditioning system.
|
Ampere
|
The rate of flow of electricity through
electric wires.
|
Apron
|
A paved area, such as the juncture of a
driveway with the street or with a garage entrance.
|
Backfill
|
The gravel or earth replaced in the space
around a building wall after foundations are in place.
|
Balusters
|
Upright supports of a balustrade rail.
|
Balustrade
|
A row of balusters topped by a rail, edging
a balcony or a staircase.
|
Baseboard
|
A board along the floor against walls and
partitions to hid gaps.
|
Batt
|
Insulation in the form of a blanket, rather
than loose filling.
|
Batten
|
Small thin strips covering joints between
wider boards on exterior building surfaces.
|
Beam
|
One of the principal horizontal wood or
steel members of a building.
|
Bearing Wall
|
A wall that supports a floor or roof of a
building.
|
Bib or Bibcock
|
A water faucet to which a hose may be
attached, also called a hose bib or sill cock.
|
Bleeding
|
Seeping of resin or gum from lumber. This
term is also used in referring to the process of drawing air from
water pipes.
|
Brace
|
A piece of wood or other material used to
form a triangle and stiffen some part of a structure.
|
Braced Framing
|
Construction technique using posts and
cross-bracing for greater rigidity.
|
Brick Veneer
|
Brick used as the outer surface of a framed
wall.
|
Bridging
|
Small wood or metal pieces placed
diagonally between floor joists.
|
Building Paper
|
Heavy paper used in walls or roofs to
dampproof.
|
Built-Up Roof
|
A roofing material applied in sealed,
waterproof layers, where there is only a slight slope to the roof.
|
Butt Joint
|
Joining point of two pieces of wood or
molding.
|
Bx Cable
|
Electricity cable wrapped in rubber with a
flexible steel outer covering.
|
Cantilever
|
A projecting beam or joist, not supported
at one end, used to support an extension of a structure.
|
Carriage
|
The member which supports the steps or
treads of a stair.
|
Casement
|
A window sash that opens on hinges at the
vertical edge.
|
Casing
|
Door and window framing.
|
Cavity Wall
|
A hollow wall formed by firmly linked
masonry walls, providing an insulating air space between.
|
Chimney Cap
|
Concrete capping around the top of chimney
bricks and around the floors to protect the masonry from the
elements.
|
Chair Rail
|
Wooden molding on a wall around a room at
the level of a chair back.
|
Chamfered Edge
|
Molding with pared-off corners.
|
Chase
|
A groove in a masonry wall or through a
floor to accommodate pipes or ducts.
|
Chimney Breast
|
The horizontal projection-usually inside a
building-of a chimney from the wall in which it is built.
|
Circuit Breaker
|
A safety device which opens (breaks) an
electric circuit automatically when it becomes overloaded.
|
Cistern
|
A tank to catch and store rain water.
|
Clapboard
|
A long thin board, thicker on one edge,
overlapped and nailed on for exterior siding.
|
Collar Beam
|
A horizontal beam fastened above the lower
ends of rafters to add rigidity.
|
Coping
|
Tile or brick used to cap or cover the top
of a masonry wall.
|
Corbel
|
A horizontal projection from a wall,
forming a ledge or supporting a structure above it.
|
Corner Bead
|
A strip of wood or metal for protecting the
external corners of plastered walls.
|
Cornice
|
Horizontal projection at the top of a wall
or under the overhanging part of the roof.
|
Course
|
A horizontal row of bricks, cinder blocks
or other masonry materials.
|
Cove Lighting
|
Concealed light sources behind a cornice or
horizontal recess which direct the light upon a reflecting
ceiling.
|
Crawl Space
|
A shallow, unfinished space beneath the
first floor of a house which has no basement, used for visual
inspection and access to pipes and ducts. Also, a shallow space in
the attic, immediately under the roof.
|
Cripples
|
Cut-off framing members above and below
windows.
|
Door Buck
|
The rough frame of a door.
|
Dormer
|
The projecting frame of a recess in a
sloping roof.
|
Double Glazing
|
An insulating window pane formed of two
thicknesses of glass with a sealed air space between them.
|
Double Hung
Windows
|
Windows with an upperand lower sash, each
supported by cords and weights.
|
Downspout Leader
|
Downspout A spout or pipe to carry rain
water down from a roof or gutters.
|
Cripples
|
A pipe for conducting rainwater from the
roof to a cistern or to the ground by way of a downspout.
|
Downspout Strap
|
A piece of metal which secures the
downspout to the eaves or wall of a building.
|
Drip
|
The projecting part of a cornice which
sheds rain water.
|
Dry Wall
|
A wall surface of plasterboard or material
other than plaster.
|
Eaves
|
The extension of roof beyond house walls.
|
Efflorescence
|
White powder that forms on the surface of
brick.
|
Effluent
|
Treated sewage from a septic tank or sewage
treatment plant.
|
Fascia
|
A flat horizontal member of a cornice
placed in a vertical position.
|
Fill-Type
Insulation
|
Loose insulating material which is applied
by hand or blown into wall spaces mechanically.
|
Flashing
|
Noncorrosive metal used around angles or
junctions in roofs and exterior walls to prevent leaks.
|
Floor Joists
|
Framing pieces which rest on outer
foundation walls and interior beams or girders.
|
Flue
|
A passageway in a chimney for conveying
smoke, gases or fumes to the outside air.
|
Footing
|
Concrete base on which a foundation sits.
|
Foundation
|
Lower parts of walls on which the structure
is built. Foundation walls of masonry or concrete are mainly below
ground level.
|
Framing
|
The rough lumber of a house-joists, studs,
rafters, and beams.
|
Furring
|
Thin wood, or metal applied to a wall to
level the surface for lathing, boarding, or plastering, to create
an insulating air space, and to damp proof the wall.
|
Fuse
|
A short plug in an electric panel box which
opens (breaks) an electrical circuit when it becomes overloaded.
|
Gable
|
The triangular part of a wall under the
inverted "v" of the roof line.
|
Gambrel Roof
|
A roof with two pitches, designed to
provide more space on upper floors. The roof is steeper on its
lower slope and flatter toward the ridge.
|
Girder
|
A main member in a framed floor supporting
the joists which carry the flooring boards. It carries the weight
of a floor or partition.
|
Glazing
|
Fitting glass into windows or doors.
|
Grade Line
|
The point at which the ground rests against
the foundation wall.
|
Green Lumber
|
Lumber which has been inadequately dried
and which tends to warp or "bleed" resin.
|
Grounds
|
Pieces of wood embedded in plaster of walls
to which skirtings are attached. Also wood pieces used to stop the
plaster work around doors and windows.
|
Gusset
|
A brace or bracket used to strengthen a
structure.
|
Gutter
|
A channel at the eaves for conveying away
rain water.
|
Hardwood
|
The close-grained wood from broad-leaved
trees such as oak or maple.
|
Headers
|
Double wood pieces supporting joists in a
floor or double wood members placed on edge over windows and doors
to transfer the roof and floor weight to the studs.
|
Heel
|
The end of a rafter that rests on the wall
plate.
|
Hip Roof
|
A roof that slants upward on three or four
sides.
|
Hip
|
The external angle formed by the juncture
of two slopes of a roof.
|
Jalousies
|
Windows with movable, horizontal glass
slats angled to admit-ventilation and keep out rain. This term is
also used for outside shutters of wood constructed in this way.
|
Jamb
|
An upright surface that lines an opening
for a door or window.
|
Joist
|
A small rectangular sectional member
arranged parallel from wall to wall in a building, or resting on
beams or girders. They support a floor or the laths or furring
strips of a ceiling.
|
Kiln-Dried
|
Artificial drying of lumber, superior to
most lumber that is air dried.
|
King-Post
|
The middle post of a truss. Large, heavy
screws, used where great strength is required, as in heavy framing
or when attaching ironwork to wood.
|
Lag-Screws or
Coach-Screws
|
Large, heavy screws, used where great
strength is required, as in heavy framing or when attaching
ironwork to wood.
|
Lally Column
|
A steel tube sometimes filled with
concrete, used to support girders or other floor beams.
|
Lath
|
One of a number of thin narrow strips of
wood nailed to rafters, ceiling joists, wall studs, etc. to make a
groundwork or key for slates, tiles, or plastering.
|
Leaching Bed
|
Tiles in the trenches carrying treated
wastes from septic tanks.
|
Ledger
|
A piece of wood which is attached to a beam
to support joists.
|
Lintel
|
The top piece over a door or window which
supports walls above the opening.
|
Load-Bearing Wall
|
A strong wall capable of supporting weight.
|
Louver
|
An opening with horizontal slats to permit
passage of air, but excluding rain, sunlight and view.
|
Masonry
|
Walls built by a mason, using brick, stone,
tile or similar materials.
|
Molding
|
A strip of decorative material having a
plane or curved narrow surface prepared for ornamental
application. These strips are often used to hide gaps at wall
junctures.
|
Moisture Barrier
|
Treated paper or metal that retards or bars
water vapor, used to keep moisture from passing into walls or
floors.
|
Mullion
|
Slender framing which divides the lights or
panes of windows.
|
Newel
|
The upright post or the upright formed by
the inner or smaller ends of steps about which steps of a circular
staircase wind. In a straight flight staircase, the principal post
at the foot or the secondary post at a landing.
|
Nosing
|
The rounded edge of a stair tread.
|
Parging
|
A rough coat of mortar applied over a
masonry wall as protection or finish; may also serve as a base for
an asphaltic waterproofing compound below grade.
|
Pilaster
|
A projection or the foundation wall used to
support a floor girder or stiffen the wall.
|
Pitch
|
The angle of slope of a roof.
|
Plasterboard (See
Dry Wall)
|
Gypsum board, used instead of plaster.
|
Plates
|
Pieces of wood placed on wall surfaces as
fastening devices. The bottom member of the wall is the sole plate
and the top member is the rafter plate.
|
Plenum
|
A chamber which can serve as a distribution
area for heating or cooling systems, generally between a false
ceiling and the actual ceiling.
|
Pointing
|
Treatment of joints in masonry by filling
with mortar to improve appearance or protect against weather.
|
Post-And-Beam
Construction
|
Wall construction in which beams are
supported by heavy posts rather than many smaller studs.
|
Prefabrication
|
Construction of components such as walls,
trusses, or doors, before delivery to the building site.
|
Rabbet
|
A groove cut in a board to receive another
board.
|
Radiant Heat
|
Coils of electricity, hot water or steam
pipes embedded in floors, ceilings, or walls to heat rooms.
|
Rafter
|
One of a series of structural roof members
spanning from an exterior wall to a center ridge beam or ridge
board.
|
Reinforced
Concrete
|
Concrete strengthened with wire or metal
bars.
|
Ridge Pole
|
A thick longitudinal plank to which the
ridge rafters of a roof are attached.
|
Riser
|
The upright piece of a stair step, from
tread to tread.
|
Roof Sheathing
|
Sheets, usually of plywood, which are
nailed to the top edges of trusses or rafters to tie the roof
together and support the roofing material.
|
Sandwich Panel
|
A panel with plastic, paper, or other
material enclosed between two layers of a different material.
|
Sash
|
The movable part of a window-the frame in
which panes of glass are set in a window or door.
|
Scotia
|
A concave molding.
|
Scuttle Hole
|
A small opening either to the attic, to the
crawl space or to the plumbing pipes.
|
Seepage Pit
|
A sewage disposal system composed of a
septic tank and a connected cesspool.
|
Septic Tank
|
A sewage settling tank in which part of the
sewage is converted into gas and sludge before the remaining waste
is discharged by gravity into a leaching bed underground.
|
Shakes
|
Handcut wood shingles.
|
Sheathing (See
Wall Sheathing)
|
The first covering of boards or material on
the outside wall or roof prior to installing the finished siding
or roof covering.
|
Shim
|
Thin tapered piece of wood used for
leveling or tightening a stair or other building element.
|
Shingles
|
Pieces of wood, asbestos or other material
used as an overlapping outer covering on walls or roofs.
|
Shiplap
|
Boards with rabbeted edges overlapping.
|
Shiplap
|
Siding Boards of special design nailed
horizontally to vertical studs with or without intervening
sheathing to form the exposed surface of outside walls of frame
buildings.
|
Sill Plate
|
The lowest member of the house framing
resting on top of the foundation wall. Also called the mud sill.
|
Skirtings
|
Narrow boards around the margin of a floor;
baseboards.
|
Slab
|
Concrete floor placed directly on earth or
a gravel base and usually about four inches thick.
|
Sleeper
|
Strip of wood laid over concrete floor to
which the finished wood floor is nailed or glued.
|
Soffit
|
The visible underwide of structural members
such as staircases, cornices, beams, a roof overhang or eave.
|
Softwood
|
Easily worked wood or wood from a
conebearing tree.
|
Soil Stack
|
Vertical plumbing pipe for waste water.
|
Stringer
|
A long, horizontal member which connects
uprights in a frame or supports a floor or the like. One of the
enclosed sides of a stair supporting the treads and risers.
|
Studs
|
In wall framing, the vertical members to
which horizontal pieces are nailed. Studs are spaced either 16
inches or 24 inches apart.
|
Subfloor
|
Usually, plywood sheets that are nailed
directly to the floor joists and that receive the finish flooring.
|
Sump
|
A pit in the basement in which water
collects to be pumped out with a sump pump.
|
Swale
|
A wide shallow depression in the ground to
form a channel for storm water drainage.
|
Tie
|
A wood member which binds a pair of
principal rafters at the bottom.
|
Tile Field
|
Open-joint drain tiles laid to distribute
septic tank effluent over an absorption area or to provide subsoil
drainage in wet areas.
|
Toenail
|
Driving nails at an angle into corners or
other joints.
|
Tongue-And-Groove
|
Carpentry joint in which the jutting edge
of one board fits into the grooved end of a similar board.
|
Trap
|
A bend in a water pipe to hold water so
gases will not escape from the plumbing system into the house.
|
Tread
|
The horizontal part of a stair step.
|
Truss
|
A combination of structural members usually
arranged in triangular units to form a rigid framework for
spanning between load-bearing walls.
|
Valley
|
The depression at the meeting point of two
roof slopes.
|
Vapor Barrier
|
Material such as paper, metal or paint
which is used to prevent vapor from passing from rooms into the
outside walls.
|
Venetian Window
|
A window with one large fixed central pane
and smaller panes at each side.
|
Vent Pipe
|
A pipe which allows gas to escape from
plumbing systems.
|
Verge
|
The edge of tiles, slates or shingles,
projecting over the gable of a roof.
|
Wainscoting
|
The lower three or four feet of an interior
wall when lined with paneling, tile or other material different
from the rest of the wall.
|
Wall Sheathing
|
Sheets of plywood, gypsum board, or other
material nailed to the outside face of studs as a base for
exterior siding.
|
Weather Stripping
|
Metal, wood, plastic or other material
installed around door and window openings to prevent air
infiltration.
|
Weep Hole
|
A small hole in a wall which permits water
to drain off.
|
|